Patented three-sided design

A pro-shop edge, in your pocket.

Tri-Cut is the first handheld skate sharpener that roughs, smooths and polishes in one tool. Cut a razor edge with a mirror-finished hollow at the rink, in the hotel, or on the bench between periods.

3abrasive sides
7/16" & 1/2"radius of hollow
100sof sharpenings
Tri-Cut handheld 3-sided ice skate sharpener in navy blue and black, showing the Rough, Smooth and Polish sharpening channels

Choose your sharpener

Figure or hockey?

Tricut Figure Skate Sharpener

White Tri-Cut figure skate sharpener with diamond-coated rods

5/8" ROH

Figure skate sharpener

Built for figure skates at a 5/8-inch radius of hollow — a shallower groove that keeps clean, controlled edges for spins, jumps and footwork.

Tricut Hockey Skate Sharpener

Navy blue Tri-Cut hockey skate sharpener with Allen key

7/16" ROH

Hockey skate sharpener

Built for hockey skates at a 7/16-inch radius of hollow — a deeper bite for hard stops, tight turns and explosive starts.

Watch it work

Ninety seconds, start to finished edge

R · S · P

Three sides. Three passes. One tool.

A machine shop does this in stages, and so does Tri-Cut — except the stages are molded into a single body you hold in one hand.

R

Rough

Cut the hollow back into a dull or nicked edge.

Wipe the blade clean, clamp the roughing side onto the steel and run the tool end to end. Roll it off both ends every few strokes so the toe and heel get cut too.

S

Smooth

Erase the scratch marks the roughing pass leaves behind.

Switch to the smoothing side and repeat the same motion. Work until the pattern disappears and the groove reads as an even satin surface.

P

Polish

Bring the hollow to a mirror finish, then knock the burr off.

Spread a pea-sized amount of compound on the edge and work the polishing side back and forth until the surface turns black. Wipe, repeat, then finish flat.

Three Tri-Cut sharpeners — blue, and black with diamond-coated rods

Diamond abrasives

Cuts steel, not just corners

The roughing rod is diamond-coated and rated for hundreds of sharpenings. It clamps to the blade with a T-handle so the tool tracks the steel instead of wandering.

Tri-Cut skate sharpener

Flat bottom, V profile

Glide speed and edge bite together

Tri-Cut's patented geometry cuts a flat-bottom hollow with a V at 7/16-inch or 1/2-inch radius of hollow. The polishing side then finishes the groove to a mirror.

Who skates on it

Built for anyone tired of the sharpening line

Hockey players

Bite back on a fresh cut without waiting on the pro-shop line between games.

Figure skaters

Keep edges consistent through practice blocks and test prep instead of resetting after every shop visit.

Hockey parents

Skip the weekly sharpening trip and the fee that comes with it, all season long.

Coaches and teams

One kit in the bench bag covers a whole roster's worth of mid-tournament emergencies.

Two ways to buy

Pick the kit that fits your bag

Tri-Cut Pro Kit laid out in its black roll-up pouch: sharpening stone, hex key, microfibre cloth, lubricant syringe and the blue three-sided sharpener guides

Tri-Cut Pro Kit

Everything needed for complete rinkside edge care.

$99
Tri-Cut three-sided handheld ice skate sharpener: blue anodised aluminium body with four hex bolts and the diamond-coated roughing rod visible through the centre slot

3-Sided Skate Sharpener

Rough, smooth and polish in one compact tool.

$68

From the inventor

Why a handheld sharpener had to exist

Tri-Cut was designed to move the pro-shop process — rough, smooth, polish — into something a skater can carry. Every detail serves a reliable finish from a tool this small.

More about Tri-Cut
Tri-Cut story video thumbnail

Common questions

Before you order

Does this replace a pro shop?

For routine sharpening and edge maintenance, yes — that is the whole point of the three-sided design. Heavily damaged steel or a blade that needs re-levelling is still a job for a machine.

Which skates does it fit?

Pick the sharpener that matches your skates: the Hockey Skate Sharpener (7/16" ROH) for hockey skates, or the Figure Skate Sharpener (5/8" ROH) for figure skates.

What hollow does it cut?

Tri-Cut's patented geometry cuts 7/16-inch and 1/2-inch radius of hollow, with a flat bottom and V profile for glide and edge together.

Stop planning your week around the sharpening shop

One tool in the bag, three sides, and a razor edge whenever you need one.

Shop Tri-Cut